Presenting The FK-1 Featuring: 400x1200x475mm Print Capacity All V-Slot Frame Construction Eliminates Smooth Rods and Linear Bearings All Printed Parts in IC3D Fun King 3D Yellow PETG (Listed on their site as “Yellow”) E3D V6 HotEnd  Bondtech Extruder Duet3D Ethernet Mainboard Auto Bed Level Correction using Antclabs BLTouch (Not currently shown in the rendered images.) 6mm (1/4”) Mic-6 Cast Aluminium Bed Trailer:   Design: 400-500 hours invested (possibly more.) Outside influence was avioded to try and make it 100% my own. (Not saying there is not anything similar out there, just that I did not seek out other’s designs.) Concept was designed around parts that are easy toRead More →

Here is the code for the YouTube Scroller. This is the basic first draft of the code. Feel free to hack it up and do stuff with it. Video is here: https://youtu.be/mDYys7uhE1M For some reason I have yet to figure out, wordpress is giving me fits about my code, so here is the code and the two supporting files you will need: https://www.funking3d.com/downloads/NodeMCU-YT-Scrollerv1.zipRead More →

Terms: Open only to users with a valid United States mailing address. (No shipping out side of the U.S.) Value of prizes: 1st = $64.95, 2nd = 61.96, 3rd = $38.97 Members of Fun King 3D and employees of AIO Robotics are not eligible to win. Prizes are courtesy of AIO Robotics. ———————————————————————————– 12 Pack (One of each color): http://amzn.to/2vSDygg All AIO Robotics Filament: http://amzn.to/2vS3RDd Fun King 3D 250 Subscriber GiveawayRead More →

This project came to life because of a basic need to have an easy (non-fumbling) way to change camera scenes in OBS (Open Broadcaster Software.) I did not want to have to look down to my keyboard and fumble around. I wanted a utility type keyboard that would allow quick and easy changes. Part 1 of this project is the initial brainstorming on what we wanted it to do: Once we knew where it was going (at least at first) we decided it was time to order some parts. Sometimes you can look at things on the internet a million times, but until it isRead More →

Here are a few steps that should help you calibrate your extruder. With 1.75mm Filament you want to use about 90mm per minute. With 3mm filament you want to use 30mm per minute.With 1.75mm Filament you want to use about 90mm per minute. With 3mm filament you want to use 30mm per minute. 1. Mark your filament at 150mm above your extruder. You can use any point of reference as long as it does not change. Something you can always reference again. 2. Using the interface of choice Pronterface, Octoprint, etc.. Send the following codes. A. G92E0 (Resets the extruder) B. G1E100F90 (Use F30 forRead More →

Sticky

Welcome to Fun King 3D (.com)! Fun King 3D is made up of a father (Glenn) and son (Xander) team who do 3D Printing and Electronics projects. We love to learn new things and we love to teach others what we know and what we learn. Most of out content is made for YouTube and it works it way here with the occasional content made for here exclusively. Look around and let us know if there is something you want to see.Read More →

If you have a 3D Printer and you are still moving your gcode to it by SD Card, then this video is for you. I have to admit that I initially setup Octoprint (Octopi) just because I thought it sounded really cool to connect a Raspberry Pi to my 3D Printer. This video will walk you through the process of installing it and getting the basic setup done. You are going to need a couple of programs to start: Octopi: https://octopi.octoprint.org/ Win32 Disk Imager: https://sourceforge.net/projects/win32diskimager/ Putty: www.putty.org One of the following 2. (AngryIP for the computer, or Fing for a mobile device.) Angry IP Scanner:Read More →

Unboxing our June Maker Box. Zach joined us for this one. It was, umm, fun. Good for some laughs. Watch the outtake at the end too. Maker Box can be found at: https://makerbox.cratejoy.com/refer/Glenn-TQTYLWEM By using the link above to sign up for Maker Box, it helps our channel a little by occasionally getting a free month! (Once you sign up, you can get a referral link too!)  Read More →

We wanted to give an update on the progress of our Anet A8. This video shows a few things we have printed and we talk about a few tweaks we have done to make the printer better. We promised in the beginning that we would not do any major upgrades until at least the 100 hour mark. We exceeded that to 125 hours. Now we will begin some serious upgrades. Link to buy the Anet A8: http://www.gearbest.com/3d-printers-3d-printer-kits/pp_343643.html?lkid=10743862 (*This is an affiliate link that helps the channel.)Read More →

This is a video series that was made step by step as we assembled our Original Prusa Research i3 Mk2s 3D Printer. Each step in the assembly process has been individually recorded. If we ran into problems, those problems and the solutions are shown in the videos. These are real time and nothing has been omitted. This way you can work through building yours at the same time if you choose to. (Click the “Read More” for the videos.)Read More →